迪威網(wǎng)友8139b5
發(fā)布時間：2021/1/21 11:18:00
The Mercenary is an Open Source FDM 3D printer currently in development.
It's a Core XY machine build with as many easy obtainable metal parts as possible.
Currently it only uses 5 mechanical printed parts.
It is easy to build and the parts can easily be sourced.
If it gets enough attention i will start creating guides and BOM's, aswell as uploading the few needed STL's.
I want to share the technology behind the printer, as some aspects are quite unique. For example it sports a belt driven Z axis on a single motor, the Z stays in Sync and the bed does not move when power is cut.
Designing and building this machine has cost me a lot of energy (And money) over the last yea.
I did quite a few revisio of the printer, but now it's time to come out with the design.
Feel free to follow me at or leave a like if you support my project.
Currently it uses a 340x340x6mm cast plate but i have a 412x412x8mm ready with Custom 230v Heater and a custom Pei Sintered Spring sheet.
Printer features:
412x412x450 mm Print Area.
Aluminum cast tooling plate as printbed, the most straight plate you can get.
3 point bed leveling.
Belt Driven Z axis: Does not go out of sync, bed does not drop even a bit when power is cut.
Core XY
200W Silent PSU 850W 230V bed heater using a Solid State Relay.
Direct Drive and Bowden, still testing what would be best.
Will be fully enclosed with PolyCarbonate
Easy to build and replicate
Uploaded parts:
Duet 2 Case. I created this small form factor case for my 4040 Extrusion, will fit 3030 and 2020 just fine. I used 2 metal brackets, but i uploaded a bracket that can be 3D printed.
BOM for the case: 4x M3 15mm or longer bolts 4x M3 Nut 4x M2 3mm or longer
It's a Core XY machine build with as many easy obtainable metal parts as possible.
Currently it only uses 5 mechanical printed parts.
It is easy to build and the parts can easily be sourced.
If it gets enough attention i will start creating guides and BOM's, aswell as uploading the few needed STL's.
I want to share the technology behind the printer, as some aspects are quite unique. For example it sports a belt driven Z axis on a single motor, the Z stays in Sync and the bed does not move when power is cut.
Designing and building this machine has cost me a lot of energy (And money) over the last yea.
I did quite a few revisio of the printer, but now it's time to come out with the design.
Feel free to follow me at or leave a like if you support my project.
Currently it uses a 340x340x6mm cast plate but i have a 412x412x8mm ready with Custom 230v Heater and a custom Pei Sintered Spring sheet.
Printer features:
412x412x450 mm Print Area.
Aluminum cast tooling plate as printbed, the most straight plate you can get.
3 point bed leveling.
Belt Driven Z axis: Does not go out of sync, bed does not drop even a bit when power is cut.
Core XY
200W Silent PSU 850W 230V bed heater using a Solid State Relay.
Direct Drive and Bowden, still testing what would be best.
Will be fully enclosed with PolyCarbonate
Easy to build and replicate
Uploaded parts:
Duet 2 Case. I created this small form factor case for my 4040 Extrusion, will fit 3030 and 2020 just fine. I used 2 metal brackets, but i uploaded a bracket that can be 3D printed.
BOM for the case: 4x M3 15mm or longer bolts 4x M3 Nut 4x M2 3mm or longer
|
共個文件
壓縮包大?。?MB
|
||
|---|---|---|
微信小程序
微信掃碼打開此模型
迪威模型
微信掃碼支付