Zoro's Katana swords 索隆三刀

本次作品是近期內最滿意的，風格與以往作品不同，由於自身喜歡古代兵器類的，因此做起來滿有幹勁的。
透過製作索隆的刀重新認識這幾把，原來索隆總共有六把刀，我省略了壞掉那幾把刀，
製作主要這三把刀，和道一字文、三代鬼撤、黑刀秋水，後來搜尋時發現似乎還有新刀(留給下次作品吧)，
3D建模雖然都是簡單指令，但仍需花些時間去處理細節特徵，透過多本體與曲面指令可以更彈性輕鬆建模。
3D列印過程比想像中還要不容易，手柄是最容易列印的，由於物件屬於細長型，
原以為可以站著印完的，沒想到因?yàn)楦哂旨?xì)，要不結構太軟跟著轉動，要不就是變比薩斜塔加牽絲，
最慘的是直接倒給你看，後來想了又想決定給他倒著印，不過相對要處理支撐材才算完整。
刀鞘支撐記得只能開外部，若內側有支撐材是無法移除的，上色一樣是不容易的，
刀與刀鞘我預留很多空間，這是必要的因?yàn)樽償?shù)太多這樣比較保險(拉絲、毛邊、垂料、塗裝厚等)，
上色沒有訣竅，只能一筆一筆慢慢塗，用心做完後這幾把刀看起來還真不錯呢。
這次的作品我首次加入了亮光透明保護層，這能使顏色更鮮豔同時具有保護功能，最近才有的想法，是一個相見恨晚的工序。
註:如果你也想嘗試亮光塗裝，請先拿實驗品來測試塗裝效果，避免成分有可能導致塑膠或顏料溶解，毀掉精心製作的成品。
有如卡通-獵人當中所敘述的，作品被製作時耗費大量的精力，最後作品周?chē)蛔⑷肓俗髡叩哪睿?br>沒有學過念卻能產生念是很不容易的，彷彿看見了作品上有自己的念(以上純屬幻想虛構XD)
This work is the most satisfactory in the near future, and the style is different from previous works. Since I like ancient weapo, I am full of motivation.
I re-recognized these by making Zoro's katana. It turned out that Sauron had a total of six knives. I omitted the broken ones.
The three main knives were produced,和道一字文、三代鬼撤、黑刀秋水. Later, when searching, I found that there are still new knives (leave it for the next work)
Although 3D modeling is easy to drawing, it still takes some time to process the detailed features. Multi-body and surface itructio can be more flexible and easy to model.
The 3D printing process is more difficult than imagined. The handle is the easiest to print. Because the objects are slim,
I thought I could finish printing while standing. I didn't expect that because the structure was too soft, it would turn too softly, or it would change the Leaning Tower of Pisa and pull the wire.
The wot thing is to show it to you directly. Later, after thinking and deciding to give him a revee print, but it is relatively complete to deal with the support material.
Scabbard support can only be opened on the outside. If there is a support material on the iide, it cannot be removed. It is not easy to color it.
I reserve a lot of space for knives and scabbards. This is necessary because there are too many variables so it is safer (drawing, burring, hanging material, thick coating, etc.),
There is no trick to coloring, you can only apply it slowly one by one. After making your heart, these knives look really good.
I have added a bright traparent protective layer for this work for the fit time. This can make the colo more vivid and have a protective function. The idea only recently has taken the work into a new stage.
Note: If you also want to try bright coating, please take the experimental product to test the coating effect, to avoid the ingredients may cause the plastic or pigment to dissolve and destroy the elaborate finished product.
As described in the cartoon-hunter, the work took a lot of energy when it was produced, and the author's mind was injected around the work.
It is not easy to produce thoughts without learning them, as if you saw your own thoughts on the work (the above is purely fantasy XD)
More 3D printing works video share