迪威網友068fa9
發布時間：2023/6/21 9:21:00
This is an African elephant with 22 movable joints.
The joint design of this elephant is different from the common chain-like design. These joints can be adjusted and fixed at different angles, allowing the elephant's trunk to be lifted and posed in various preferred positions. The tightness of the joints depends on the hardness of the materials used for printing. Using harder materials will result in tighter joints.
The reason it is named "Blank" is to encourage the printer to add color to the elephant's body. For those with multi-color 3D printers, they can try printing each segment in different colors.
When printing, please start by printing the tail. If the tail can rotate properly, then use the same printing settings to print the other parts. If the tail gets stuck and cannot rotate, please reduce the material flow to continue printing.
Printer - Bambu Lab X1 Series
3D printing settings
Layer height - 0.2mm
Infill Density - 12%
No supports.
多關節素坯非洲象
這是一隻有22個可轉動關節的非洲象
這隻非洲象的關節設計與常見的鍊條式的設計不同，這種關節可以調整角度後固定，因此這隻大象的鼻子可以抬起並且擺出自己喜歡的姿態。大象的關節結緊迫程度與使用的材料硬度有關，使用愈硬的材料列印則關節的緊度愈緊。
之所以取名為(白胚)的原因，就是鼓勵列印者能幫大象的身體上顏色，若有多色3D列印機的朋友就可以試著在每一段使用不一樣的色彩列印。
列印建議
列印時請先列印尾巴，若尾巴能正常轉動，就以相同列印設定來列印其他部分。若尾巴卡住無法轉動，請減少材料流量來列印。
層高-0.2mm
免支撐
填充-12%
作品列印機-Bambu Lab X1 Series
The joint design of this elephant is different from the common chain-like design. These joints can be adjusted and fixed at different angles, allowing the elephant's trunk to be lifted and posed in various preferred positions. The tightness of the joints depends on the hardness of the materials used for printing. Using harder materials will result in tighter joints.
The reason it is named "Blank" is to encourage the printer to add color to the elephant's body. For those with multi-color 3D printers, they can try printing each segment in different colors.
When printing, please start by printing the tail. If the tail can rotate properly, then use the same printing settings to print the other parts. If the tail gets stuck and cannot rotate, please reduce the material flow to continue printing.
Printer - Bambu Lab X1 Series
3D printing settings
Layer height - 0.2mm
Infill Density - 12%
No supports.
多關節素坯非洲象
這是一隻有22個可轉動關節的非洲象
這隻非洲象的關節設計與常見的鍊條式的設計不同，這種關節可以調整角度後固定，因此這隻大象的鼻子可以抬起並且擺出自己喜歡的姿態。大象的關節結緊迫程度與使用的材料硬度有關，使用愈硬的材料列印則關節的緊度愈緊。
之所以取名為(白胚)的原因，就是鼓勵列印者能幫大象的身體上顏色，若有多色3D列印機的朋友就可以試著在每一段使用不一樣的色彩列印。
列印建議
列印時請先列印尾巴，若尾巴能正常轉動，就以相同列印設定來列印其他部分。若尾巴卡住無法轉動，請減少材料流量來列印。
層高-0.2mm
免支撐
填充-12%
作品列印機-Bambu Lab X1 Series
|
共個文件
壓縮包大?。?MB
|
||
|---|---|---|
微信小程序
微信掃碼打開此模型
迪威模型
微信掃碼支付