迪威網友f32dac
發布時間：2020/12/15 0:17:00
MD CPAP
Ender 3 CPAP add-on with x4 5015
This thingi lets you use CPAP pipes and x4 5015 blowe to replace the bullseye or Hero Me 2 and its single 4010 stock blower. This provides more cold air at slightly lower noise, or a lot of cold air with a lot of noise...
Update 2020-01-12
Tweaked bullseye duct to now blow air slightly forward from where it did before. Also added a bltouch mount to the left side of the duct. Less parts = lighter carriage MD_CPAP_bullseye_20200112_update.sdl. Print with supports and in black ;)
Update 2019-11-07
After some long testing and tweaking I have a new Bullseye duct (fit photo) which also includes a beam for stability and some led light mounting option. Also created a better fan mount, this fits the 5015 fa tighter with less gaps and is all in one print (second photo). Also has the output facing forwards so you can use shorter cpap pipe.
You don't really need to but I modified the marlin firmware so the fan min value matches the lowest number that will get these fa to spin. As well as enabling the fan blip to 100% mostly because it sounds cool.
Configuration_adv.h:
#define FAN_KICKSTART_TIME 500
#define FAN_MIN_PWM 84
#define FAN_MAX_PWM 255
In my (Prusa)Slicer:
Fan speed Min: 1%
Fan speed Max: 60%
Bridge fan speed: 80%
These work for me, you will be different due to fa, length of cpap, slicer, filament, temperatures etc etc etc
Update 2019-04-08
Also uploaded a Hero Me 2 veion of the CPAP adapte and a matching bltouch mount as the original one on the Hero Me 2 gets in the way. I find the Hero Me 2 desig to be more compact and has a wider air outlet compared to the bullseye, but both are good. In the photos the black prints are the Bullseye and the blue prints are the Hero Me 2 veion.
A 4020 mount for ( so i can put this on top of my Ender 3 as shown in the photo.
Running the fa of a mosfet just to be safe (one with red heat sink) with room for an extra dc-dc converter for 12V hot end fan in the future.
This also requires a Petsfang part, the BULLSEYE_BASE_CREALITY_9 ( Petsfang do a lot of awesome work in boosting the performance of the Ender 3.
And some custom wire clips to make it all nice and neat
Print 0.1mm layer height and in black! (0.2mm also works fine)
Thanks to all the desig already on thingivee that made this possible.
Enjoy
Ender 3 CPAP add-on with x4 5015
This thingi lets you use CPAP pipes and x4 5015 blowe to replace the bullseye or Hero Me 2 and its single 4010 stock blower. This provides more cold air at slightly lower noise, or a lot of cold air with a lot of noise...
Update 2020-01-12
Tweaked bullseye duct to now blow air slightly forward from where it did before. Also added a bltouch mount to the left side of the duct. Less parts = lighter carriage MD_CPAP_bullseye_20200112_update.sdl. Print with supports and in black ;)
Update 2019-11-07
After some long testing and tweaking I have a new Bullseye duct (fit photo) which also includes a beam for stability and some led light mounting option. Also created a better fan mount, this fits the 5015 fa tighter with less gaps and is all in one print (second photo). Also has the output facing forwards so you can use shorter cpap pipe.
You don't really need to but I modified the marlin firmware so the fan min value matches the lowest number that will get these fa to spin. As well as enabling the fan blip to 100% mostly because it sounds cool.
Configuration_adv.h:
#define FAN_KICKSTART_TIME 500
#define FAN_MIN_PWM 84
#define FAN_MAX_PWM 255
In my (Prusa)Slicer:
Fan speed Min: 1%
Fan speed Max: 60%
Bridge fan speed: 80%
These work for me, you will be different due to fa, length of cpap, slicer, filament, temperatures etc etc etc
Update 2019-04-08
Also uploaded a Hero Me 2 veion of the CPAP adapte and a matching bltouch mount as the original one on the Hero Me 2 gets in the way. I find the Hero Me 2 desig to be more compact and has a wider air outlet compared to the bullseye, but both are good. In the photos the black prints are the Bullseye and the blue prints are the Hero Me 2 veion.
A 4020 mount for ( so i can put this on top of my Ender 3 as shown in the photo.
Running the fa of a mosfet just to be safe (one with red heat sink) with room for an extra dc-dc converter for 12V hot end fan in the future.
This also requires a Petsfang part, the BULLSEYE_BASE_CREALITY_9 ( Petsfang do a lot of awesome work in boosting the performance of the Ender 3.
And some custom wire clips to make it all nice and neat
Print 0.1mm layer height and in black! (0.2mm also works fine)
Thanks to all the desig already on thingivee that made this possible.
Enjoy
|
共個文件
壓縮包大?。?MB
|
||
|---|---|---|
微信小程序
微信掃碼打開此模型
迪威模型
微信掃碼支付