迪威網(wǎng)友f677e5
發(fā)布時間：2021/1/17 5:44:00
FALL THANK YOU PROMOTION:
Anyone interested in buying one of my complete assembled/tested hot end cartridges I am offering $15 off at my Tindie store from October 14-31, 2019. Use promo code TYFALL2019
Tindie store:
This thing makes it easier to itall an E3D V6 hot end in a XYZ da Vinci 1.0 Pro printer by merely unclamping/unplugging the stock extruder module, traferring the PCB and fan from the stock extruder cartridge to this thing, assembling the E3D V6 with the heater cartridge and thermistor from the stock extruder, mounting the E3D V6 hot end in this thing and then plugging/clamping this thing into the daVinci Pro in place of the stock extruder module.
Note that this design is specific to the E3D V6's dimeio. I have a hot end that purports to be an E3D V6 clone, but other than the mounting collar at the top the dimeio are all off. The overall height is about a centimeter more which is really too much to use with this configuration -- of coue, I suppose you could make an exteion for the Z-axis stop flag and just remember that you're z-axis print volume will be a bit less. However, the heatsink diameter is also a couple of millimete larger which get's pretty tight in the Pro's carriage.
AVAILABLE PRE-PRINTED
If you are interested in purchasing this thing pre-printed, it is available from PrintIt Industries at: You will still need to provide the hot end, fan, PCB and assembly hardware.
ALSO AVAILABLE ASSEMBLED AND TESTED
I sell fully assembled and tested replacement cartridges made with genuine E3D hot end components. If you are interested in an assembled cartridge you can look to see if I have any cartridges available in my Tindie store:
PCB ONLY ALSO AVAILABLE
I also sell just my replacement PCB for the hot end cartridge. These are also available via my Tindie store:
Anyone interested in buying one of my complete assembled/tested hot end cartridges I am offering $15 off at my Tindie store from October 14-31, 2019. Use promo code TYFALL2019
Tindie store:
This thing makes it easier to itall an E3D V6 hot end in a XYZ da Vinci 1.0 Pro printer by merely unclamping/unplugging the stock extruder module, traferring the PCB and fan from the stock extruder cartridge to this thing, assembling the E3D V6 with the heater cartridge and thermistor from the stock extruder, mounting the E3D V6 hot end in this thing and then plugging/clamping this thing into the daVinci Pro in place of the stock extruder module.
Note that this design is specific to the E3D V6's dimeio. I have a hot end that purports to be an E3D V6 clone, but other than the mounting collar at the top the dimeio are all off. The overall height is about a centimeter more which is really too much to use with this configuration -- of coue, I suppose you could make an exteion for the Z-axis stop flag and just remember that you're z-axis print volume will be a bit less. However, the heatsink diameter is also a couple of millimete larger which get's pretty tight in the Pro's carriage.
AVAILABLE PRE-PRINTED
If you are interested in purchasing this thing pre-printed, it is available from PrintIt Industries at: You will still need to provide the hot end, fan, PCB and assembly hardware.
ALSO AVAILABLE ASSEMBLED AND TESTED
I sell fully assembled and tested replacement cartridges made with genuine E3D hot end components. If you are interested in an assembled cartridge you can look to see if I have any cartridges available in my Tindie store:
PCB ONLY ALSO AVAILABLE
I also sell just my replacement PCB for the hot end cartridge. These are also available via my Tindie store:
|
共個文件
壓縮包大?。?MB
|
||
|---|---|---|
微信小程序
微信掃碼打開此模型
迪威模型
微信掃碼支付