Glasses_Adapters_for_Full_Facepieces

這是適配全面罩防毒面具的兩種眼鏡架設計，可適配如3M 6800、霍尼韋爾54001、思創S100系列，只有一個鏡片的全面罩防毒面具。 應當與大部分全面罩防毒面具適配，但是和有左右雙目鏡片的面具適配不佳，更基本地，需要防毒面具內部空間放得下你的眼鏡。 These are two designs of glasses adapters for full facepiece/gas mask such as 3M 6800 or Honeywell 54001, which features a single lens. Should be able to work with the majority of full facepieces, but not with facepieces with two lens, or more basically, lacks internal space to let your glasses fit in. 文件中的臂和短臂可按需選擇，其他文件基本都會用到。 對我來說，我使用的是卡槽版本，配兩個短臂。如果你需要，可以選擇一個臂和一個短臂，僅一個短臂，或任何能配合你所用面罩的組合。 我用的是一副舊眼鏡，因?yàn)檠坨R腿要拆掉，你可以也用舊眼鏡或者買一副便宜眼鏡。 The arms and short arms in the file can be chosen to suit your need, but other STLs basically all need to be used. For my use case, I use the slot version with two short arms. If you need, you can select one arm and one short arm, only one short arm, or any combination that works with your gasmask. I use a pair of old glasses, since the legs of glasses need to be removed, you may use an old pair or buy a cheap pair of glasses for the build. 對于卡槽版本，你需要N 1個M312螺絲（N是你選用的延長臂數量）和螺母，杯頭盤頭都可以。還要一根扎帶來固定眼鏡，雙面膠來固定slot piece和arm base，兩個直徑8mm 高度2mm的圓柱形磁鐵，一些納米膠來把整個支架粘在面罩鏡片上（寬度20mm或15mm皆可）。 For the slot version, you'll need N 1 M312 bolts(N is the quantity of arms you use) and nuts, SHCS or BHCS are all fine. And a ziptie to mount your glasses to the claw, normal double sided tape to mount slot piece with arm base, two cylindrical magnets(8mm in diameter and 2mm in height), some VHB tape to mount the whole adapter to your gasmask(20mm or 15mm in width). 關于打印件，你需要： As to prints, you'll need Claw_for_Glasses1, Arm_Base1, Slot_Base1, Slot_Piece1, and arms, type and quantity based on you requirement. 對于磁吸版本，你需要N 1個M312螺絲（N是你選用的延長臂數量）、兩個M322螺絲和螺母，杯頭盤頭都可以。還要一根扎帶來固定眼鏡，四個直徑12mm高度8mm的圓柱形磁鐵， 一些帶膠防滑墊來防止支架發生位移。 For the magnet version(yes I know slot version also features magnets), you'll need N 1 M312 bolts(N is the quantity of arms you use), two M322 bolts and nuts, SHCS or BHCS are all fine. A ziptie to mount your glasses to the claw, four cylindrical magnets(12mm in diameter and 8mm in height), some elastic pads with double sided tape to prevent movement of adapter and glasses after installing adapter to your gasmask. 關于打印件，你需要： As to prints, you'll need Claw_for_Glasses1, Holder_to_Arm1, Inner_Magnet_Holder2, Outer_Magnet_Holder2, and arms, type and quantity based on you requirement. 可能需要強力膠來固定磁鐵。為了螺絲孔的強度，你可以在切片時將螺絲方向調為垂直于熱床。 Superglue maybe needed to secure magnets. You may orient the parts to make screw direction vertical to hot bed when slicing in order to get good strength around the screw holes. 如果你愿意，可以來B站看看我的演示視頻，也可以加QQ群來交流。 And if you wish, you may come to visit my bilibili account( for demonstration videos or join my QQ group(850474972) to communicate or have some chats.