迪威網(wǎng)友a(bǔ)669c9
發(fā)布時間：2020/12/19 20:38:00
Summary
I bought a Unihertz Atom XL phone with radio, and couldn't find pre-made car and belt mounts. So I mucked around and remixed and re-designed a few things, and here are the results.
If they are not perfect, I apologise. Feel free to further modify and remix to suit youelf.
These STL's are for three different mix & match car mounting methods, plus as a Belt Clip for the Unihertz Atom XL Phone/Radio.
I suggest printing them out of PETG, 100% infill, with supports (where appropriate). PETG resists up to about 80 degrees C, and has a bit of flex which is useful. As the walls are quite thin, 100% infil strengthe the models.
MODELS:
1) A Case designed originally for a Belt but useable in the car as below. I suggest printing it standing up,
2) The clip for (1) above. It's too hard to print together, too much supports so it was easier for me to print separately laying on a thin side. Then gluing it.
3) CD Mount for 1) & 2). Print flat side down. Theoretically you should still be able to play Cd's with it ierted.
4) Full size case to mount on a car. Print flat side down. You can glue either 2) or 6) style connector to it.
If you want to refine this one it's on TINKERCAD:-
5) An Each-way-Vent-Mount (either horizontal or Vertical vents). Use with the case (1) plus Clip (2)
6) Each Way Vent Connector, to be glued to your choice of case. Print round flat side on bed.
I want to thank the uploade from whom I borrowed & remixed bits from the following:
Suggestio for Glue:
Methyl Ethyl Ketone (MEK) also known as Acrylic Glue
or
3M VHB (Very High Bond) tape- Red
And possibly super glue.
Enjoy!
Raffy, VK2RF
I bought a Unihertz Atom XL phone with radio, and couldn't find pre-made car and belt mounts. So I mucked around and remixed and re-designed a few things, and here are the results.
If they are not perfect, I apologise. Feel free to further modify and remix to suit youelf.
These STL's are for three different mix & match car mounting methods, plus as a Belt Clip for the Unihertz Atom XL Phone/Radio.
I suggest printing them out of PETG, 100% infill, with supports (where appropriate). PETG resists up to about 80 degrees C, and has a bit of flex which is useful. As the walls are quite thin, 100% infil strengthe the models.
MODELS:
1) A Case designed originally for a Belt but useable in the car as below. I suggest printing it standing up,
2) The clip for (1) above. It's too hard to print together, too much supports so it was easier for me to print separately laying on a thin side. Then gluing it.
3) CD Mount for 1) & 2). Print flat side down. Theoretically you should still be able to play Cd's with it ierted.
4) Full size case to mount on a car. Print flat side down. You can glue either 2) or 6) style connector to it.
If you want to refine this one it's on TINKERCAD:-
5) An Each-way-Vent-Mount (either horizontal or Vertical vents). Use with the case (1) plus Clip (2)
6) Each Way Vent Connector, to be glued to your choice of case. Print round flat side on bed.
I want to thank the uploade from whom I borrowed & remixed bits from the following:
Suggestio for Glue:
Methyl Ethyl Ketone (MEK) also known as Acrylic Glue
or
3M VHB (Very High Bond) tape- Red
And possibly super glue.
Enjoy!
Raffy, VK2RF
|
共個文件
壓縮包大?。?MB
|
||
|---|---|---|
微信小程序
微信掃碼打開此模型
迪威模型
微信掃碼支付